voici pour installation de 3.4TEPS TO INSTALL A 3.4 IN A FIERO
Getting Started
1. Initial steps
These are all detailed in your shop manual.
o Remove the engine cradle from the Fiero and place it on the cradle dolly. Note: If your car has A/C, be sure to seal the A/C lines where you detach the compressor hoses. Use something that will keep moisture and critters out, but will not leave any debris behind.
o Separate the engine from the transmission and remove it from the cradle.
o Undress the 2.8 down to the longblock in preparation for the 3.4 transfer.
2. 3.4 Engine Choices
o If you choose to get a new engine, the one you want is GM part number 12363230. I've seen it for around $1800 as of this writing. You'll also need to get the 17# injectors for the '93-'95 Camaro/Firebird, which are the same part for a Chevy 305 (5.0) engine too. The injectors from a Ford 5.0 will also work, but since they are a 19# variety you will need an adjustable fuel pressure regulator to use these. Otherwise your air/fuel mixture will be too rich and will foul your spark plugs, reduce fuel economy, increase exhaust emissions and may damage your catalytic converter.
o If you choose to get a used engine, the one you want is from a 1993-1995 Camaro or Firebird. You will need to strip it all the way down to the longblock (heads, block and all internal mechanicals, including the balancer). Use of the oil pan will be discussed later. Remove and keep the fuel injectors from the 3.4's fuel rail, as they are a 17# higher-flow type than the 15# ones on the 2.8. Be careful removing them from the rail and inspect the O-ring seals for re-use. The original Fiero fuel pressure regulator on the fuel rail will work fine with these injectors. Everything else that may be included with the engine - flywheel/flexplate, intake plenum, intake manifold, fuel rail, water pump, timing cover, wiring harness, pulleys, modules, brackets, sensors, plug wires, etc. should be placed in a big box. You may be able to get a credit back from the recycler for these parts. Also remove the metal plug that blocks the distributor hole, and clip the wires from the crankshaft position sensor at the harmonic balancer on the 3.4. The Fiero ECM does not use this sensor, and it keeps the hole plugged in the block by leaving it installed.
These engines usually go for about $500-$800 depending on mileage and demand/availability. I paid $650 for my current engine, with 51k miles on it, and two others have paid $450 for 68k and 74k engines. The higher the mileage over 50k, the more you'll want to consider replacing the cam and lifters while you've got the engine and pushrods out, since this will affect the "newness" feeling to the engine's drivability and its longevity. An excellent deal is the Crane Compucam 2030 Series Cam/Lifter Kit, which you can get from any decent speed shop, or Jeg's and Summit have it online for under $200. Joe Wynman is also reputed to have a better custom grind for 3.4's.
3. You'll need a complete gasket set for the intake manifold, plenum, timing cover, rocker covers, water pump, EGR valve, and exhaust manifold. Anywhere there is a part that you are reinstalling that had a gasket, you should basically scrape off the old one thoroughly and replace it. Also, if the engine has over 40k miles on it, you should seriously consider replacing the rear main oil seal. This is a common problem on 60 degree V6 and small-block V8 engines.
4. Mount the 3.4 on an engine stand, and make sure it is well drained of fluids so it doesn't spill out more every time you flip the engine around. The thread size of the bell housing bolts needed to mount on a stand are M12x1.75 available at most hardware / autoparts stores. Check your stand to determine the length of the shank.
5. Remove the oil filter adapter from the 3.4 and put it in the leftovers box. Transfer the threaded oil filter shaft from the 2.8 to the 3.4 by unscrewing it from the center with a 10mm hex-head wrench.
6. Flywheel/Flexplate mounting:
o For manual transmission cars:
„X On 1988s, transfer the flywheel from the 2.8 to the 3.4. It is a neutrally balanced flywheel, which you will need for the 3.4.
„X All other years need an '88 flywheel or the flywheel from the 3.4 DOHC/TDC engine. The latter weighs about 5lbs more but costs 1/3 as much.
Nathan's note: for 85-87 cars, you may modify your existing flywheel professionally or do it yourself in 30-45 minutes if you have access to a die grinder. I have not priced out how much it would be to have it done professionally, but doing it yourself isn't much of a burden. There's an obvious lug of weight on the front side of the flywheel that needs to be removed and leveled to the rest of the flywheel surface. After it is smooth and flat, take some paint and cover up the exposed metal to deter corrosion.
o For automatics:
„X 1988: Transfer your 2.8's flexplate to the 3.4.
„X Others: You will need a 1988 Fiero flexplate, or a 3.1/3.4TDC flexplate.
Relocating the Starter
The trickiest part to the 3.4 conversion is getting the starter bolts drilled on the left side of the engine block. There are lots of ways to do this. One is you can buy a drill-guide template made by Ed Parks at the Fiero Factory for about $75. Alternatively, you can use the starter itself as your template. If you choose to go this route, we've found a way to make this a lighter task. If not, go your own way and continue at step 8.
7. Begin by mounting the appropriate flywheel (from step 6) on the 3.4. Then take the starter from the 2.8 and remove the selenoid, which is the small silver cylinder held on by two bolts. There is also a tab that is wedged into the starter body. To avoid damaging the starter, you may need to loosen the long screws that hold on the cover for the motor itself. Remove the selenoid and spring and keep in a safe place (ie, not the floor so you can easily "access" it with your foot
With the selenoid removed, you can extend the pinion gear so that it lines up with the flywheel. You want to have a nice overlap. As a side note, if there is any error in placement, make it so that the starter is slightly closer to the flywheel. This way, you can shim the starter back from the flywheel. On the flip side, if you mount the starter further away from the flywheel, you have no recourse.
Align the starter with the flywheel on the side of the engine where the oil filter goes (same position as it was on the 2.
. You will need an assistant for this part. One person needs to hold the starter in place while the other person drills out the two holes necessary to secure the starter in place. Get a drill and tap set for an M10x1.5 hole (should be a 21/64" or 8.5mm drill bit) and drill the two holes, making sure that you stay perfectly straight drilling into the block. When doing the inner (flat) hole, you may find it is easier to use a center punch and drill it out. While drilling, be sure to use plenty of 3-in-1 oil and have your helper check squareness often with a carpenter's square. The hole on the outer edge of the block must be drilled into metal which is on a 45 degree angle; this is challenging to say the least, and you only get one shot at it. Use the starter as a template as you drill this hole.
8. Once the holes are drilled, tap threads into them with the M10x1.5 tap. The inner hole should be tapped from the bottom, but the outer hole (the angled one) is easier to tap from the top.
Reminders on tapping: use lots of oil, and if it's really cold outside get the tap warm before attempting this or it could fracture inside the hole. You do not want this to happen to you.
Spray out the holes with brake cleaner, and you can now mount your Fiero starter on the 3.4 block. Use starter shims as necessary to get a proper strike from the starter pinion gear.
9. If your engine was used, while you're in the tapping mood you should also tap out the exhaust manifold bolt holes on the head to clean them up. Use an M8x1.25 tap. You are also well advised to replace all of the exhaust manifold bolts. They are M8x1.25x26, 13MM head, Grade 8 (PN 11515757) and are also compatible with Saturn engines, so you shouldn't have any trouble finding them at a larger dealership. It's a good idea to use hi-temp anti-seize on them. It will stink to high heaven when you first fire it, but will be worth it when you need to remove them again. The exhaust manifold gasket you will need is Fel-Pro part # MS-93045. Don't attempt to substitute the less-expensive 3.4 exhaust gasket. It is made of a completely different material and will leak, causing excess heat in your engine bay, spewing uncatalyzed exhaust into the air just behind your head, and generally annoying you with strange sewing-machine noises and engine ticks. Click here for more information on this subject. Also, since the engine is stripped down, it's a good idea to tap out any other holes you will use on it. This is not that hard (or expensive) of a task, and is a good idea since many of the holes will need to be precisely torqued. The three common tap sizes are:
o M8 1.25 (fine)
o M10 1.5 (coarse)
o M12 1.75 (coarse)
Additional Engine Modifications
10. Bellhousing
Using a large, 7/16" - 1/2" drill bit, drill out the threads of the right-most bellhousing bolt hole on the engine. This is where a bolt will pass through to the transmission opposite all the others. If an M12x1.75 bolt will pass through it freely, the hole should be large enough. We had trouble with the alignment on the bellhousing with this hole - the first attempts resulted in the bolt not feeding to the hole at the correct angle - so make sure you can hand-tighten the bolt into the transmission case before you attempt to use a wrench on it. Otherwise you will cross-thread and strip it, and Helicoil kits for this large a metric-size hole are difficult to find and very expensive (>$80). Do not ask how I know this. The transmission case is made of aluminum and the threads are very fragile, so be extremely careful on this step.
11. Block Chop
For cars with automatic transmissions, you will find that part of the block in this area will be in the way of the transmission housing. You will need to cut away part of the block to clear it, a 45* cutoff similar to what is already on the starter side of the block.
12. Oil Pan
o If you have an 85-86 car, use the 2.8 oil pan.
o If you have an 87-88 car, use the 3.4 oil pan, with an "impact persuasion" modification for engine mount clearance. I'm told you may also be able to use the 2.8 pan for a better fit, but you would at least need to transfer the 2.8 oil pickup as well because the 2.8 oil pan's baffles are different from the 3.4.
13. Timing Cover
You will need to remove the harmonic balancer from both engines for the timing cover transfer. Do not attempt to remove it with a gear puller or you will damage it. Use only a harmonic balancer puller for this. Again, familiarize yourself with chapter 2 in a Haynes manual, or the Engine chapter in an equivalent manual. Also, remove the 3.4's crank pulley and put it in the leftovers box.
14. Cleaning Gasket Surfaces
Be sure to clean all gasket material from both sides of the timing cover's surfaces. This can be a very time-consuming operation. The cover is made of aluminum and is thus very fragile. Be extremely careful if you use a gasket scraper or you will damage it. Also, a recommended sealant for the timing cover and water pump gaskets is a blue goop called Hylomar HPF. Use disposable gloves with this stuff because it basically never cures.
15. Water Pump
Now is the time to replace your water pump if you choose to do so. Otherwise reuse the Fiero's water pump. Do not attempt to use the 3.4's water pump or timing cover as its flow is backwards that of the Fiero, and the timing cover is also missing a necessary boss to attach the lower A/C bracket. If you buy a new pump, you will need to transfer the plug from the old pump to the new one. This may require a torch to free.
16. Harmonic Balancer
You will need to transfer the timing mark on the 2.8 balancer to the 3.4 balancer. To do this, align the crankshaft notches on both balancers, and use a ruler at the 2.8 notch to mark the new notch on the 3.4 balancer. You can use a Dremel or a Hacksaw for this, then coat the notch with a clear coat enamel so it won't rust and turn orange.
17. Accessory Transfer
Begin transferring the 2.8's accessories and brackets to your new engine. You will need to install the new fuel injectors onto the Fiero's fuel rail, using the best O-rings from the two sets you will have. You will need to remove all 12 pushrods to install the intake manifold gasket. Follow the instructions in your shop manual on how to do this, as it will involve keeping them in the exact same locations when reinstalling them and setting valve lash. Use blue threadlocker on the intake and timing cover/water pump and any other bolts/studs you feel are prudent. There is a plug in the hole of the 3.4 block where the distributor installs from the 2.8, which you'll need to remove with a large set of pliers if you didn't already do this during the 3.4 teardown phase. When you transfer the distributor to the 3.4, align the balancer on the crankshaft with 0 degrees on the timing tab, then point the distributor's rotor at plug #1 on the cap (trace back to the plug closest to the alternator, this is plug #1). This will make your life a lot easier when you go to start it up for the first time, rather than having to guess at the correct distributor/balancer alignment. Also, inspect the black rubber O-ring on the distributor shaft. If it is not pliable and cross-sectionally round, it should be replaced or you will have an oil leak.
18. Oil Pressure Sender and A/C Compressor
If you do not have air conditioning, screw the oil pressure sender directly into the block at the oil filter, without its adapter fitting from the 2.8. Otherwise:
o 1985-1987 cars will either need to weld an M10 30mm Grade 8 bolt into the back of the engine shock bracket and grind down the head for block clearance (very tight there), or will need to tap the hole in that bracket to screw a bolt directly into it. The other side of the lower compressor bracket attaches to a boss on the front of the Fiero timing cover, but this is not on other 2.8 covers. If you would prefer not to do this modification yourself, you can purchase a modified original shock-mount bracket from Ed Parks at the Fiero Factory, or a new custom-made piece from Rodney Dickman is also being offered.
o Because they have no engine shock, 1988 cars will need the shock bracket from an 85-87 car with an 85-87 lower engine mount bracket, or Rodney's custom mount for the lower A/C bracket as mentioned above. See his contact information at the end of this document.
o All cars which have air conditioning will need a special 5/16"F - 1/2"M brass adapter fitting for the oil pressure sender tube. (I am not absolutely certain of the dimensions of this part, please let me know if it is not correct. The male end must be the same size as the end of the oil pressure sender.) You can see it in this picture. This isn't a hardware-store item, though it may seem like one. Try your local speed shop, autoparts store, or dealership parts store. I have also asked Rodney Dickman to provide these with his 1988 bracket as a kit. Even though it appears to screw into the block directly, the flange on the tube does not seal properly to the existing fitting and will leak a steady stream of oil when you start the new engine.
Recharging the A/C system with R-134a once you reassemble the system is a discussion for a separate document.
19. Clutch
Now is the best time to install a new clutch on manual-transmission cars, because you are about to mate the engine back to the transmission. Don't skimp on this part because it's a ***** to replace it again if it breaks. Opinion is divided on upgrading. A stock/OEM clutch is acceptable, but may not last as long as something like a Centerforce if you are hard on clutches.
20. Mounts
Don't waste your time or money on the OEM rubber transmission mounts. The new rubber trans mounts hit their stops very easily. They're inadequate for this engine. Replace front and rear transmission mounts with polyurethane mounts from West Coast Fiero .
Installing the engine back on the cradle
Once you have installed the lower engine mount bracket to the bottom front of the engine, lift the engine up about three feet using an engine hoist, and align it over the cradle. Slowly lower the engine into place, taking care to seat the transmission tailshaft into the center of the flywheel/flexplate, and the lower engine mount bracket onto the lower engine mount. You may have to turn both wheels in order to get the tailshaft splines to seat properly. You can then bolt the engine to the transmission. When you install the bellhousing bolt which is backwards all the rest, be sure to note step 10 above.
Your conversion is now complete. Follow the instructions in your shop manual to reinstall the cradle into the car and you're finished!
